OmronCipNet 类

Instantiate a communication object for a OmronCipNet PLC protocol

Specify the IP address and port to instantiate a communication object for a OmronCipNet PLC protocol

当前的数据变换机制，当你需要从字节数据转换类型数据的时候需要。
The current data transformation mechanism is required when you need to convert type data from byte data.

获取或设置整个交互指令的控制码，默认为0x6F，通常不需要修改
Gets or sets the control code of the entire interactive instruction. The default is 0x6F, and usually does not need to be modified.

获取或设置当前的管道信息，管道类型为CommunicationPipe的继承类，内置了PipeTcpNet管道，PipeUdpNet管道，PipeSerialPort管道等

当前连接的唯一ID号，默认为长度20的guid码加随机数组成，方便列表管理，也可以自己指定
The unique ID number of the current connection. The default is a 20-digit guid code plus a random number.

获取或设置接收服务器反馈的时间，如果为负数，则不接收反馈
Gets or sets the time to receive server feedback, and if it is a negative number, does not receive feedback

获取或是设置远程服务器的IP地址，如果是本机测试，那么需要设置为127.0.0.1
Get or set the IP address of the remote server. If it is a local test, then it needs to be set to 127.0.0.1

获取或设置绑定的本地的IP地址和端口号信息，如果端口设置为0，代表任何可用的端口
Get or set the bound local IP address and port number information, if the port is set to 0, it means any available port

组件的日志工具，支持日志记录，只要实例化后，当前网络的基本信息，就以DEBUG等级进行输出
The component's logging tool supports logging. As long as the instantiation of the basic network information, the output will be output at DEBUG

获取或设置当前的通信的消息路由信息，可以实现一些复杂情况的通信，数据包含背板号，路由参数，slot，例如：1.15.2.18.1.1
Get or set the message routing information of the current communication, which can realize some complicated communication. The data includes the backplane number, routing parameters, and slot, for example: 1.15.2.18.1.1

获取或设置服务器的端口号，具体的值需要取决于对方的配置
Gets or sets the port number of the server. The specific value depends on the configuration of the other party.

port and slot information

获取或设置接收服务器反馈的时间，如果为负数，则不接收反馈
Gets or sets the time to receive server feedback, and if it is a negative number, does not receive feedback

获取或设置在发送通信报文前追加发送的字节信息，HEX格式，通常用于lora组网时，需要携带 00 00 00 02 四个字节的站地址功能。
Obtain or set the byte information sent before sending communication packets, HEX format, usually used for LORA networking, you need to carry 00 00 00 02 four-byte station address function.

The current session handle, which is determined by the PLC when communicating with the PLC handshake

获取或设置在正式接收对方返回数据前的时候，需要休息的时间，当设置为0的时候，不需要休息。
Get or set the time required to rest before officially receiving the data from the other party. When it is set to 0, no rest is required.

Gets or sets the slot number information for the current plc, which should be set before connections

获取或设置客户端的Socket的心跳时间信息，这个是Socket底层自动实现的心跳包，不基于协议层实现。默认小于0，不开启心跳检测，如果需要开启，设置 60_000 比较合适，单位毫秒
Get or set the heartbeat time information of the Socket of the client. This is the heartbeat packet automatically implemented by the bottom layer of the Socket, not based on the protocol layer. The default value is less than 0, and heartbeat detection is not enabled. If you need to enable it, it is more appropriate to set 60_000, in milliseconds.

一个字单位的数据表示的地址长度，西门子为2，三菱，欧姆龙，modbusTcp就为1，AB PLC无效
The address length represented by one word of data, Siemens is 2, Mitsubishi, Omron, modbusTcp is 1, AB PLC is invalid

创建一个读取多标签的报文
Build a read command bytes

创建一个读取标签的报文指定，标签地址可以手动动态指定slot编号，例如 slot=2;AAA
Build a read command bytes, The label address can manually specify the slot number dynamically, for example slot=2;AAA

Create a written message instruction

Create a written message instruction

手动断开与远程服务器的连接，如果当前是长连接模式，那么就会切换到短连接模式
Manually disconnect from the remote server, if it is currently in long connection mode, it will switch to short connection mode

手动断开与远程服务器的连接，如果当前是长连接模式，那么就会切换到短连接模式
Manually disconnect from the remote server, if it is currently in long connection mode, it will switch to short connection mode

尝试连接远程的服务器，如果连接成功，就切换短连接模式到长连接模式，后面的每次请求都共享一个通道，使得通讯速度更快速
Try to connect to a remote server. If the connection is successful, switch the short connection mode to the long connection mode. Each subsequent request will share a channel, making the communication speed faster.

尝试连接远程的服务器，如果连接成功，就切换短连接模式到长连接模式，后面的每次请求都共享一个通道，使得通讯速度更快速
Try to connect to a remote server. If the connection is successful, switch the short connection mode to the long connection mode. Each subsequent request will share a channel, making the communication speed faster.

决定当前的消息是否是用于问答机制返回的消息，默认直接返回 true, 实际的情况需要根据协议进行重写方法
To determine whether the current message is the message returned by the question answering mechanism, the default is true. In actual cases, the rewriting method needs to be performed according to the protocol

Performs application-defined tasks associated with freeing, releasing, or resetting unmanaged resources.

Performs application-defined tasks associated with freeing, releasing, or resetting unmanaged resources.

Determines whether the specified object is equal to the current object.

和服务器交互完成的时候调用的方法，可以根据读写结果进行一些额外的操作，具体的操作需要根据实际的需求来重写实现
The method called when the interaction with the server is completed can perform some additional operations based on the read and write results. The specific operations need to be rewritten according to actual needs.

根据实际的协议选择是否重写本方法，有些协议在断开连接之前，需要发送一些报文来关闭当前的网络通道
Select whether to rewrite this method according to the actual protocol. Some protocols need to send some packets to close the current network channel before disconnecting.

根据实际的协议选择是否重写本方法，有些协议在断开连接之前，需要发送一些报文来关闭当前的网络通道
Select whether to rewrite this method according to the actual protocol. Some protocols need to send some packets to close the current network channel before disconnecting.

Allows an object to try to free resources and perform other cleanup operations before it is reclaimed by garbage collection.

Serves as the default hash function.

获取当前的报文进行日志记录的时候，是否使用二进制的格式记录，默认返回 LogMsgFormatBinary，重写可以根据session对象分别返回不同记录模式
Whether to log the current packet in binary format, the default return is LogMsgFormatBinary. If you want to override it, different recording modes can be returned according to session

获取一个新的消息对象的方法，需要在继承类里面进行重写
The method to get a new message object needs to be overridden in the inheritance class

Gets the Type of the current instance.

一个字单位的数据表示的地址长度，西门子为2，三菱，欧姆龙，modbusTcp就为1，AB PLC无效
The address length represented by one word of data, Siemens is 2, Mitsubishi, Omron, modbusTcp is 1, AB PLC is invalid

获取写入数据的长度信息，此处直接返回数组的长度信息

根据实际的协议选择是否重写本方法，有些协议在创建连接之后，需要进行一些初始化的信号握手，才能最终建立网络通道。
Whether to rewrite this method is based on the actual protocol. Some protocols require some initial signal handshake to establish a network channel after the connection is created.

根据实际的协议选择是否重写本方法，有些协议在创建连接之后，需要进行一些初始化的信号握手，才能最终建立网络通道。
Whether to rewrite this method is based on the actual protocol. Some protocols require some initial signal handshake to establish a network channel after the connection is created.

对当前设备的IP地址进行PING的操作，返回PING的结果，正常来说，返回Success
PING the IP address of the current device and return the PING result. Normally, it returns Success

使用日志记录一个接收的报文信息
` Logs are used to record information about a received packet

使用日志记录一个接收的报文信息
` Logs are used to record information about a received packet

使用日志记录一个发送的报文信息
Logs are used to record information about a send packet

使用日志记录一个发送的报文信息
Logs are used to record information about a send packet

Creates a shallow copy of the current Object.

将所有的cip指定进行打包操作。

对当前的命令进行打包处理，通常是携带命令头内容，标记当前的命令的长度信息，需要进行重写，否则默认不打包
The current command is packaged, usually carrying the content of the command header, marking the length of the current command, and it needs to be rewritten, otherwise it is not packaged by default

[商业授权] 批量读取多地址的数据信息，例如我可以读取两个标签的数据 "A","B[0]"，每个地址的数据长度为1，表示一个数据，最终读取返回的是一整个的字节数组，需要自行解析
[Authorization] Batch read data information of multiple addresses, for example, I can read the data of two tags "A", "B[0]", the data length of each address is 1, which means one data, and the final read returns a The entire byte array, which needs to be parsed by itself

[商业授权] 批量读取多地址的数据信息，例如我可以读取两个标签的数据 "A","B[0]"， 长度为 [1, 5]，返回的是一整个的字节数组，需要自行解析
[Authorization] Read the data information of multiple addresses in batches. For example, I can read the data "A", "B[0]" of two tags, the length is [1, 5], and the return is an entire byte array, and I need to do it myself Parsing

读取指定地址的二进制数据内容，长度为地址长度，一般都是1，除非读取数组时，如果需要强制使用 片段读取功能码，则地址里携带 x=0x52; 或是 x=82; 则强制使用片段读取。
Read the binary data content of the specified address, the length is the address length, generally 1, unless the array is read, if you need to force the fragment reading function code, the address carries x=0x52; or x=82; then the fragment read is forced.

读取支持Hsl特性的数据内容，该特性为HslDeviceAddressAttribute，详细参考api文档说明，或是官网的详细文档
Read the data content of the Hsl attribute. The attribute is HslDeviceAddressAttribute, please refer to the api documentation for details.

[商业授权] 批量读取多地址的数据信息，例如我可以读取两个标签的数据 "A","B[0]"，每个地址的数据长度为1，表示一个数据，最终读取返回的是一整个的字节数组，需要自行解析
[Authorization] Batch read data information of multiple addresses, for example, I can read the data of two tags "A", "B[0]", the data length of each address is 1, which means one data, and the final read returns a The entire byte array, which needs to be parsed by itself

[商业授权] 批量读取多地址的数据信息，例如我可以读取两个标签的数据 "A","B[0]"， 长度为 [1, 5]，返回的是一整个的字节数组，需要自行解析
[Authorization] Read the data information of multiple addresses in batches. For example, I can read the data "A", "B[0]" of two tags, the length is [1, 5], and the return is an entire byte array, and I need to do it myself Parsing

读取指定地址的二进制数据内容，长度为地址长度，一般都是1，除非读取数组时，如果需要强制使用 片段读取功能码，则地址里携带 x=0x52; 或是 x=82; 则强制使用片段读取。
Read the binary data content of the specified address, the length is the address length, generally 1, unless the array is read, if you need to force the fragment reading function code, the address carries x=0x52; or x=82; then the fragment read is forced.

异步读取支持Hsl特性的数据内容，该特性为HslDeviceAddressAttribute，详细参考api文档说明
Asynchronously read the data content of the Hsl attribute. The attribute is HslDeviceAddressAttribute, please refer to the api documentation for details.

读取单个的bool数据信息，如果读取的是单bool变量，就直接写变量名，如果是由int组成的bool数组的一个值，一律带"i="开头访问，例如"i=A[0]"
Read a single bool data information, if it is a single bool variable, write the variable name directly, if it is a value of a bool array composed of int, it is always accessed with "i=" at the beginning, for example, "i=A[0]"

批量读取Boolean数组信息，需要指定地址和长度，返回Boolean 数组
Batch read Boolean array information, need to specify the address and length, return Boolean array

批量读取的bool数组信息，如果你有个Bool数组变量名为 A, 那么读第0个位，可以通过 ReadBool("A")，但是第二个位需要使用 ReadBoolArray("A[0]") // 返回32个bool长度，0-31的索引，如果我想读取32-63的位索引，就需要 ReadBoolArray("A[1]") ，以此类推。
For batch read bool array information, if you have a Bool array variable named A, then you can read the 0th bit through ReadBool("A"), but the second bit needs to use ReadBoolArray("A[0]" ) // Returns the length of 32 bools, the index is 0-31, if I want to read the bit index of 32-63, I need ReadBoolArray("A[1]"), and so on.

批量读取的bool数组信息，如果你有个Bool数组变量名为 A, 那么读第0个位，可以通过 ReadBool("A")，但是第二个位需要使用 ReadBoolArray("A[0]") // 返回32个bool长度，0-31的索引，如果我想读取32-63的位索引，就需要 ReadBoolArray("A[1]") ，以此类推。
For batch read bool array information, if you have a Bool array variable named A, then you can read the 0th bit through ReadBool("A"), but the second bit needs to use ReadBoolArray("A[0]" ) // Returns the length of 32 bools, the index is 0-31, if I want to read the bit index of 32-63, I need ReadBoolArray("A[1]"), and so on.

读取单个的bool数据信息，如果读取的是单bool变量，就直接写变量名，如果是由int组成的bool数组的一个值，一律带"i="开头访问，例如"i=A[0]"
Read a single bool data information, if it is a single bool variable, write the variable name directly, if it is a value of a bool array composed of int, it is always accessed with "i=" at the beginning, for example, "i=A[0]"

异步批量读取Boolean数组信息，需要指定地址和长度，返回Boolean 数组
Asynchronously batch read Boolean array information, need to specify the address and length, return Boolean array

读取PLC的byte类型的数据
Read the byte type of PLC data

读取PLC的byte类型的数据
Read the byte type of PLC data

使用CIP报文和服务器进行核心的数据交换

使用CIP报文和服务器进行核心的数据交换

读取自定义的数据类型，需要继承自IDataTransfer接口，返回一个新的类型的实例对象。
To read a custom data type, you need to inherit from the IDataTransfer interface and return an instance object of a new type.

读取自定义的数据类型，需要继承自IDataTransfer接口，传入一个实例，对这个实例进行赋值，并返回该实例的对象。
To read a custom data type, you need to inherit from the IDataTransfer interface, pass in an instance, assign a value to this instance, and return the object of the instance.

读取自定义的数据类型，需要继承自IDataTransfer接口，返回一个新的类型的实例对象。
To read a custom data type, you need to inherit from the IDataTransfer interface and return an instance object of a new type.

读取自定义的数据类型，需要继承自IDataTransfer接口，传入一个实例，对这个实例进行赋值，并返回该实例的对象。
To read a custom data type, you need to inherit from the IDataTransfer interface, pass in an instance, assign a value to this instance, and return the object of the instance.

读取指定地址的日期数据，最小日期为 1970年1月1日，当PLC的变量类型为 "Date" 和 "TimeAndDate" 时，都可以用本方法读取。
Read the date data of the specified address. The minimum date is January 1, 1970. When the PLC variable type is "Date" and "TimeAndDate", this method can be used to read.

读取指定地址的日期数据，最小日期为 1970年1月1日，当PLC的变量类型为 "Date" 和 "TimeAndDate" 时，都可以用本方法读取。
Read the date data of the specified address. The minimum date is January 1, 1970. When the PLC variable type is "Date" and "TimeAndDate", this method can be used to read.

读取双浮点的数据
Read double floating point data

读取双浮点数据的数组
Read double floating point data array

异步读取双浮点的数据
Asynchronously read double floating point data

异步读取双浮点数据的数组
Asynchronously read double floating point data array

使用EIP报文和服务器进行核心的数据交换

使用EIP报文和服务器进行核心的数据交换

读取单浮点数据
Read single floating point data

读取单浮点精度的数组
Read single floating point array

异步读取单浮点数据
Asynchronously read single floating point data

异步读取单浮点精度的数组
Asynchronously read single floating point array

将二进制的数据发送到管道中去，然后从管道里接收二进制的数据回来，并返回是否成功的结果对象。
Send binary data to the pipeline, and then receive binary data back from the pipeline, and return whether the success of the result object

将多个数据报文按顺序发到设备，并从设备接收返回的数据内容，然后拼接成一个Byte[]信息，需要重写UnpackResponseContent(Byte, Byte)方法才能返回正确的结果。
Send multiple data packets to the device in sequence, and receive the returned data content from the device, and then splicing them into a Byte[] message, you need to rewrite UnpackResponseContent(Byte, Byte) method to return the correct result.

将二进制的数据发送到管道中去，然后从管道里接收二进制的数据回来，并返回是否成功的结果对象。
Send binary data to the pipeline, and then receive binary data back from the pipeline, and return whether the success of the result object

使用指定的管道来进行数据通信，发送原始数据到管道，然后从管道接收相关的数据返回，本方法无锁

将二进制的数据发送到管道中去，然后从管道里接收二进制的数据回来，并返回是否成功的结果对象。
Send binary data to the pipeline, and then receive binary data back from the pipeline, and return whether the success of the result object

将多个数据报文按顺序发到设备，并从设备接收返回的数据内容，然后拼接成一个Byte[]信息，需要重写UnpackResponseContent(Byte, Byte)方法才能返回正确的结果。
Send multiple data packets to the device in sequence, and receive the returned data content from the device, and then splicing them into a Byte[] message, you need to rewrite UnpackResponseContent(Byte, Byte) method to return the correct result.

将二进制的数据发送到管道中去，然后从管道里接收二进制的数据回来，并返回是否成功的结果对象。
Send binary data to the pipeline, and then receive binary data back from the pipeline, and return whether the success of the result object

使用指定的管道来进行数据通信，发送原始数据到管道，然后从管道接收相关的数据返回，本方法无锁

读取16位的有符号的整型数据
Read 16-bit signed integer data

读取16位的有符号整型数组
Read 16-bit signed integer array

异步读取16位的有符号的整型数据
Asynchronously read 16-bit signed integer data

异步读取16位的有符号整型数组
Asynchronously read 16-bit signed integer array

读取32位的有符号整型
Read 32-bit signed integer

读取32位有符号整型数组
Read 32-bit signed integer array

异步读取32位的有符号整型
Asynchronously read 32-bit signed integer

异步读取32位有符号整型数组
Asynchronously read 32-bit signed integer array

读取64位的有符号整型
Read 64-bit signed integer

读取64位的有符号整型数组
Read 64-bit signed integer array

异步读取64位的有符号整型
Asynchronously read 64-bit signed integer

异步读取64位的有符号整型数组
Asynchronously read 64-bit signed integer array

从PLC里读取当前PLC的型号信息
Read the current PLC model information from the PLC

从PLC里读取当前PLC的型号信息
Read the current PLC model information from the PLC

Read Segment Data Array form plc, use address tag name

Read Segment Data Array form plc, use address tag name

读取字符串数据，默认为UTF8编码
Read string data, default is the UTF8 encoding

使用指定的编码，读取字符串数据
Reads string data using the specified encoding

读取字符串数据，默认为UTF8编码
Read string data, default is the UTF8 encoding

异步使用指定的编码，读取字符串数据
Asynchronously reads string data using the specified encoding

读取结构体类型的数据，根据结构体自身的定义，读取原始字节数组，然后解析出实际的结构体数据，结构体需要实现HslStructAttribute特性

读取结构体类型的数据，根据结构体自身的定义，读取原始字节数组，然后解析出实际的结构体数据，结构体需要实现HslStructAttribute特性

从PLC里读取一个指定标签名的原始数据信息及其数据类型信息
Read the original data information of a specified tag name and its data type information from the PLC

从PLC里读取一个指定标签名的原始数据信息及其数据类型信息
Read the original data information of a specified tag name and its data type information from the PLC

读取指定地址的时间数据，最小时间为 0，如果获取秒，可以访问 TotalSeconds，当PLC的变量类型为 "Time" 和 "TimeOfDate" 时，都可以用本方法读取。
Read the time data of the specified address. The minimum time is 0. If you get seconds, you can access TotalSeconds. When the PLC variable type is "Time" and "TimeOfDate", you can use this Method to read.

读取指定地址的时间数据，最小时间为 0，如果获取秒，可以访问 TotalSeconds，当PLC的变量类型为 "Time" 和 "TimeOfDate" 时，都可以用本方法读取。
Read the time data of the specified address. The minimum time is 0. If you get seconds, you can access TotalSeconds. When the PLC variable type is "Time" and "TimeOfDate", you can use this Method to read.

读取16位的无符号整型
Read 16-bit unsigned integer

读取16位的无符号整型数组
Read 16-bit unsigned integer array

异步读取16位的无符号整型
Asynchronously read 16-bit unsigned integer

异步读取16位的无符号整型数组
Asynchronously read 16-bit unsigned integer array

读取32位的无符号整型
Read 32-bit unsigned integer

读取32位的无符号整型数组
Read 32-bit unsigned integer array

异步读取32位的无符号整型
Asynchronously read 32-bit unsigned integer

异步读取32位的无符号整型数组
Asynchronously read 32-bit unsigned integer array

读取64位的无符号整型
Read 64-bit unsigned integer

读取64位的无符号整型的数组
Read 64-bit unsigned integer array

异步读取64位的无符号整型
Asynchronously read 64-bit unsigned integer

异步读取64位的无符号整型的数组
Asynchronously read 64-bit unsigned integer array

将当前的通信对象设置DTU模式，允许传入现成的管道，并返回初始化结果，如果该设备重写了握手报文，就是返回握手结果
Set the current communication object to DTU mode, allow the existing pipe to be passed in, and return the initialization result, if the device rewrites the handshake packet, the handshake result is returned

将当前的通信对象设置DTU模式，允许传入现成的管道，并返回初始化结果，如果该设备重写了握手报文，就是返回握手结果
Set the current communication object to DTU mode, allow the existing pipe to be passed in, and return the initialization result, if the device rewrites the handshake packet, the handshake result is returned

V11版本及之前设置长连接的方法，在V12版本以上中没有任何效果，默认长连接，删除调用即可，此处保留方法是为了部分用户保持兼容性升级。
The method of setting the long connection in V11 and before, has no effect in V12 and above. this method can be deleted. The method is retained here to maintain compatibility upgrades for some users.

枚举结构体的方法，传入结构体的标签对象，返回结构体子属性标签列表信息，子属性有可能是标量数据，也可能是另一个结构体。
The method of enumerating the structure, passing in the tag object of the structure, and returning the tag list information of the sub-attributes of the structure. The sub-attributes may be scalar data or another structure.

枚举当前的所有的变量名字，包含结构体信息，除去系统自带的名称数据信息
Enumerate all the current variable names, including structure information, except the name data information that comes with the system

枚举当前的所有的变量名字，包含结构体信息，除去系统自带的名称数据信息
Enumerate all the current variable names, including structure information, except the name data information that comes with the system

Returns a string that represents the current object.

根据对方返回的报文命令，对命令进行基本的拆包，例如各种Modbus协议拆包为统一的核心报文，还支持对报文的验证
According to the message command returned by the other party, the command is basically unpacked, for example, various Modbus protocols are unpacked into a unified core message, and the verification of the message is also supported

等待指定地址的Boolean值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the Boolean value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的Int16值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the Int16 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的Int32值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the Int32 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的Int64值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the Int64 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的UInt16值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the UInt16 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的UInt32值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the UInt32 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的UInt64值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the UInt64 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的Boolean值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the Boolean value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的Int16值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the Int16 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的Int32值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the Int32 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的Int64值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the Int64 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的UInt16值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the UInt16 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的UInt32值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the UInt32 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

等待指定地址的UInt64值为指定的值，可以指定刷新数据的频率，等待的超时时间，如果超时时间为-1的话，则是无期限等待。
Waiting for the UInt64 value of the specified address to be the specified value, you can specify the frequency of refreshing the data, and the timeout time to wait. If the timeout time is -1, it is an indefinite wait.

写入double数据，返回是否成功
Write double data, return whether the write was successful

写入short数据，返回是否成功
Write short data, returns whether success

写入int数据，返回是否成功
Write int data, return whether the write was successful

写入long数据，返回是否成功
Write long data, return whether the write was successful

写入float数据，返回是否成功
Write float data, return whether the write was successful

写入字符串信息，编码为ASCII
Write string information, encoded as ASCII

写入ushort数据，返回是否成功
Write ushort data, return whether the write was successful

写入uint数据，返回是否成功
Write uint data, return whether the write was successful

写入ulong数据，返回是否成功
Write ulong data, return whether the write was successful

写入单个Bool的数据信息。如果读取的是单bool变量，就直接写变量名，如果是bool数组的一个值，一律带下标访问，例如a[0]
Write the data information of a single Bool. If the read is a single bool variable, write the variable name directly, if it is a value of the bool array, it will always be accessed with a subscript, such as a[0]

批量写入Boolean数组数据，返回是否成功
Batch write Boolean array data, return whether the write was successful

当前写入字节数组使用数据类型 0xD1 写入，如果其他的字节类型需要调用 WriteTag(String, UInt16, Byte, Int32) 方法来实现。
The currently written byte array is written using the data type 0xD1. If other byte types need to be called WriteTag(String, UInt16, Byte, Int32) Method to achieve.

写入double数组，返回是否成功
Write double array, return whether the write was successful

写入short数组，返回是否成功
Write short array, return whether the write was successful

写入int[]数组，返回是否成功
Write int array, return whether the write was successful

写入long数组，返回是否成功
Write long array, return whether the write was successful

写入float数组，返回是否成功
Write float array, return whether the write was successful

写入ushort数组，返回是否成功
Write ushort array, return whether the write was successful

写入uint[]数组，返回是否成功
Write uint array, return whether the write was successful

写入ulong数组，返回是否成功
Write ulong array, return whether the write was successful

写入Byte数据，返回是否写入成功，默认使用类型 0xC2, 如果PLC的变量类型不一样，则需要指定实际的变量类型，例如PLC的变量 A 是0xD1类型，那么地址需要携带类型信息，type=0xD1;A
Write Byte data and return whether the writing is successful. The default type is 0xC2. If the variable types of the PLC are different, you need to specify the actual variable type. For example, the variable A of the PLC is of type 0xD1, then the address needs to carry the type information, type= 0xD1;A

写入指定长度的字符串信息，如果超出，就截断字符串，如果长度不足，那就补0操作，编码为ASCII
Write string information of the specified length. If it exceeds the value, the string is truncated. If the length is not enough, it is filled with 0 and the encoding is ASCII.

写入字符串信息，需要指定的编码信息
Write string information, need to specify the encoding information

写入指定长度的字符串信息，如果超出，就截断字符串，如果长度不足，那就补0操作，编码为指定的编码信息
Write string information of the specified length. If it exceeds the value, the string is truncated. If the length is not enough, then the operation is complemented with 0 , you should specified the encoding information

写入支持Hsl特性的数据，返回是否写入成功，该特性为HslDeviceAddressAttribute，详细参考api文档说明
Write data that supports the Hsl attribute, and return whether the write was successful. The attribute is HslDeviceAddressAttribute, please refer to the api documentation for details.

异步写入double数据，返回是否成功
Asynchronously write double data, return whether the write was successful

异步写入short数据，返回是否成功
Asynchronously write short data, returns whether success

异步写入int数据，返回是否成功
Asynchronously write int data, return whether the write was successful

异步写入long数据，返回是否成功
Asynchronously write long data, return whether the write was successful

异步写入float数据，返回是否成功
Asynchronously write float data, return whether the write was successful

异步写入字符串信息，编码为ASCII
Asynchronously write string information, encoded as ASCII

异步写入ushort数据，返回是否成功
Asynchronously write ushort data, return whether the write was successful

异步写入uint数据，返回是否成功
Asynchronously write uint data, return whether the write was successful

异步写入ulong数据，返回是否成功
Asynchronously write ulong data, return whether the write was successful

写入单个Bool的数据信息。如果读取的是单bool变量，就直接写变量名，如果是bool数组的一个值，一律带下标访问，例如a[0]
Write the data information of a single Bool. If the read is a single bool variable, write the variable name directly, if it is a value of the bool array, it will always be accessed with a subscript, such as a[0]

批量写入Boolean数组数据，返回是否成功
Batch write Boolean array data, return whether the write was successful

当前写入字节数组使用数据类型 0xD1 写入，如果其他的字节类型需要调用 WriteTag(String, UInt16, Byte, Int32) 方法来实现。
The currently written byte array is written using the data type 0xD1. If other byte types need to be called WriteTag(String, UInt16, Byte, Int32) Method to achieve.

写入double数组，返回是否成功
Write double array, return whether the write was successful

写入short数组，返回是否成功
Write short array, return whether the write was successful

写入int[]数组，返回是否成功
Write int array, return whether the write was successful

写入long数组，返回是否成功
Write long array, return whether the write was successful

写入float数组，返回是否成功
Write float array, return whether the write was successful

写入ushort数组，返回是否成功
Write ushort array, return whether the write was successful

写入uint[]数组，返回是否成功
Write uint array, return whether the write was successful

写入ulong数组，返回是否成功
Write ulong array, return whether the write was successful

写入Byte数据，返回是否写入成功，默认使用类型 0xC2, 如果PLC的变量类型不一样，则需要指定实际的变量类型，例如PLC的变量 A 是0xD1类型，那么地址需要携带类型信息，type=0xD1;A
Write Byte data and return whether the writing is successful. The default type is 0xC2. If the variable types of the PLC are different, you need to specify the actual variable type. For example, the variable A of the PLC is of type 0xD1, then the address needs to carry the type information, type= 0xD1;A

异步写入指定长度的字符串信息，如果超出，就截断字符串，如果长度不足，那就补0操作，编码为ASCII
Asynchronously write string information of the specified length. If it exceeds the value, the string is truncated. If the length is not enough, it is filled with 0 and the encoding is ASCII.

异步写入字符串信息，需要指定的编码信息
Asynchronously write string information, need to specify the encoding information

异步写入指定长度的字符串信息，如果超出，就截断字符串，如果长度不足，那就补0操作，编码为指定的编码信息
Asynchronously write string information of the specified length. If it exceeds the value, the string is truncated. If the length is not enough, then the operation is complemented with 0 , you should specified the encoding information

异步写入支持Hsl特性的数据，返回是否写入成功，该特性为HslDeviceAddressAttribute，详细参考api文档说明
Asynchronously write data that supports the Hsl attribute, and return whether the write was successful. The attribute is HslDeviceAddressAttribute, please refer to the api documentation for details.

写入自定义类型的数据，该类型必须继承自IDataTransfer接口
Write data of a custom type, which must inherit from the IDataTransfer interface

写入自定义类型的数据，该类型必须继承自IDataTransfer接口
Write data of a custom type, which must inherit from the IDataTransfer interface

使用日期格式（Date）将指定的数据写入到指定的地址里，PLC的地址类型变量必须为 "Date"，否则写入失败。
Use the date format (Date) to write the specified data to the specified address. The PLC address type variable must be "Date", otherwise the writing will fail.

使用日期格式（Date）将指定的数据写入到指定的地址里，PLC的地址类型变量必须为 "Date"，否则写入失败。
Use the date format (Date) to write the specified data to the specified address. The PLC address type variable must be "Date", otherwise the writing will fail.

使用指定的类型写入指定的节点数据，类型信息参考API文档，地址支持协议类型代号信息，例如 "type=0xD1;A"
Use the specified type to write the specified node data. For type information, refer to the API documentation. The address supports protocol type code information, such as "type=0xD1;A"

使用指定的类型写入指定的节点数据，类型信息参考API文档，地址支持协议类型代号信息，例如 "type=0xD1;A"
Use the specified type to write the specified node data. For type information, refer to the API documentation. The address supports protocol type code information, such as "type=0xD1;A"

使用时间格式（TIME）将时间数据写入到PLC中指定的地址里去，PLC的地址类型变量必须为 "TIME"，否则写入失败。
Use the time format (TIME) to write the time data to the address specified in the PLC. The PLC address type variable must be "TIME", otherwise the writing will fail.

使用日期格式（Date）将指定的数据写入到指定的地址里，PLC的地址类型变量必须为 "Date"，否则写入失败。
Use the date format (Date) to write the specified data to the specified address. The PLC address type variable must be "Date", otherwise the writing will fail.

使用日期格式（Date）将指定的数据写入到指定的地址里，PLC的地址类型变量必须为 "Date"，否则写入失败。
Use the date format (Date) to write the specified data to the specified address. The PLC address type variable must be "Date", otherwise the writing will fail.

使用时间格式（TIME）将时间数据写入到PLC中指定的地址里去，PLC的地址类型变量必须为 "TIME"，否则写入失败。
Use the time format (TIME) to write the time data to the address specified in the PLC. The PLC address type variable must be "TIME", otherwise the writing will fail.

使用时间格式（TimeOfDate）将时间数据写入到PLC中指定的地址里去，PLC的地址类型变量必须为 "TimeOfDate"，否则写入失败。
Use the time format (TimeOfDate) to write the time data to the address specified in the PLC. The PLC address type variable must be "TimeOfDate", otherwise the writing will fail.

使用时间格式（TimeOfDate）将时间数据写入到PLC中指定的地址里去，PLC的地址类型变量必须为 "TimeOfDate"，否则写入失败。
Use the time format (TimeOfDate) to write the time data to the address specified in the PLC. The PLC address type variable must be "TimeOfDate", otherwise the writing will fail.

设置日志记录报文是否二进制，如果为False，那就使用ASCII码
Set whether the log message is binary, if it is False, then use ASCII code

获取当前对象的JSON格式表示的字符串。
Gets the string represented by the JSON format of the current object.